Eaton Cutler-Hammer
Eaton Cutler-Hammer Drives
Eaton Cutler-Hammer PLC
Eaton Cutler-Hammer Circuit Breakers
Allen Bradley Panelview
Allen Bradley PLC
GE Fanuc
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
Rockwell Disclaimer: The product is used surplus. Urgent Automation is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Urgent Automation is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, Urgent Automation makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Urgent Automation also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Urgent Automation also makes no representations as to your right to install any such firmware on the product. Urgent Automation will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
The D100CR40A is one of many configurations of Cutler-Hammer’s D100 Micro Programmable Logic Controllers (PLCs). This family of PLCs is small in size, very economical, and makes use of true ladder logic programming. The D100CR40A is a 40 I/O controller with a manual, high-speed counter and is capable of being expanded with an analog input expandable module. The D100CR40A has a 115 Volt AC power input; it's 40 I/O are made up of twenty-four 24 Volt DC inputs along with 16 relay outputs. The Controller’s I/O can be expanded through the use of expanders, up to 80 I/O, broken down into 48 inputs and 32 outputs. The D100CR40A also has a high-speed counter of up to 4 kHz; as with members of its family, it has flip-flop, 16 timers, 16 counters, master control, jump, one-shot, step sequence, and comes with a 1K RAM memory.
The D100CR40A can also have analog capabilities, as it can have an analog input module connected to it; this module, which must be installed before the controller, adds two analog inputs to the controller, independent of the controller’s total I/O count. Only one analog input module can be connected to a controller, and each of the two analog input channels (each having twelve points that can be set) is capable of three input voltage ranges, namely 0 to 10 Volts, 0 to 5 Volts and 0 to 20 milliamperes DC. The signals received from these channels are translated to a register value, which is then placed in an assigned register. All the twelve registers have their values preset and the signal register is continuously checked against the preset values in the registers, in order to control the system’s circuits. The DC100CR40A weighs approximately 3 pounds and 6 ounces (1.5 kilograms) and must be installed in a protected environment with an ambient temperature of 32 to 140 degrees Fahrenheit and stored within a temperature range of 5 to 167 degrees Fahrenheit. High power control panels and high voltage must be kept away from the immediate surroundings of the controller.
| Manufacturer | Eaton Cutler-Hammer |
| Brand | Eaton Cutler-Hammer |
| Part Number/Catalog No. | D100CR40A |
| Product Type | 40 I/O Controller |
| Power Supply | 115V AC |
| Inputs | 24 |
| Input Type | 24V DC |
| Outputs | 16 |
| Output Type | Relay |
| System Max I/O Inputs | 48 |
| System Max. I/O Outputs | 32 |
| Capability | High Speed Count and Analog |
| Manufacturer | Eaton Cutler-Hammer |
| Brand | Eaton Cutler-Hammer |
| Part Number/Catalog No. | D100CR40A |
| Product Type | 40 I/O Controller |
| Power Supply | 115V AC |
| Inputs | 24 |
| Input Type | 24V DC |
| Outputs | 16 |
| Output Type | Relay |
| System Max I/O Inputs | 48 |
| System Max. I/O Outputs | 32 |
| Capability | High Speed Count and Analog |
Please refer to the manual for more information about the D100CR40A such as the wiring diagrams, data sheets, firmware information and migration or obsolescence details.
| Revision Part # | Also Known as | Availability |
D100CR40A Ser A |
D100CR40A/A, Series A, Rev A |