Eaton Cutler-Hammer
Eaton Cutler-Hammer Drives
Eaton Cutler-Hammer PLC
Eaton Cutler-Hammer Circuit Breakers
Allen Bradley Panelview
Allen Bradley PLC
GE Fanuc
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
Rockwell Disclaimer: The product is used surplus. Urgent Automation is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Urgent Automation is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, Urgent Automation makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Urgent Automation also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Urgent Automation also makes no representations as to your right to install any such firmware on the product. Urgent Automation will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
The Cutler-Hammer EDS3175 is a complete molded case circuit breaker. The device has 3 poles and it is appropriate to be used at 240 Volts AC (at 50 to 60 Hertz) or at 125 Volts DC. To protect the electrical circuits, this device will use the thermal magnetic release mechanism. The circuit breaker is sealed at the factory and users cannot change its tripping unit. The Cutler-Hammer EDS3175 passes the UL489 certification, which requires manufacturers to install internal accessories at the factory site. Always check the completeness of the MCCB after unpacking it and look closely for possible damage on the module before mounting it in the system.
The current rating of the MCCB is 175 Amps. This rating is valid, tested, and calibrated for 40 degrees Celsius (104 degrees Fahrenheit). The interrupting capacity of the EDS3175 is 10 kAIC at 125 Volts DC and 42 kAIC at 240 Volts AC. If users are applying this circuit breaker to protect motor circuitry, then this device should be rated at at least 115% of the full load current rating of the motor it is being applied to. Pulsating loads require special attention to prevent any nuisance tripping of the circuit breaker. The Eaton Cutler-Hammer EDS3175 has a highly-isolated housing with dimensions of 3.4 inches x 6.0 inches x 2.8 inches (86 millimeters x 152 millimeters x 70 millimeters). The weight of the MCCB is 3 pounds (1.4 kilograms). The installation procedure includes attaching the circuit breaker to mounting panels over predrilled holes. The devices should be tightly fixed with mounting screws, washers, and nuts.
| Part Number/Catalog No. | EDS3175 |
| Product Type | Molded Case Circuit Breaker |
| Series | C |
| Frame | F |
| Pole(s) | 3 |
| Trip Amps | 42 kA at 240 Volts |
| Interrupting Capacity | 4.5 pounds |
| Weight | Thermal-Magnetic |
| Trip Unit | 4.13 x 6 x 3.38 inches |
| Part Number/Catalog No. | EDS3175 |
| Product Type | Molded Case Circuit Breaker |
| Series | C |
| Frame | F |
| Pole(s) | 3 |
| Trip Amps | 42 kA at 240 Volts |
| Interrupting Capacity | 4.5 pounds |
| Weight | Thermal-Magnetic |
| Trip Unit | 4.13 x 6 x 3.38 inches |