FDC2175

Preowned

Includes a 1-Year UrgentAutomation warranty.

UrgentAutomation is not an authorized distributor for Eaton Cutler-Hammer.

Rated 4.9 with 18 reviews

UrgentAutomation sells surplus and refurbished products which are sourced through independent channels. All warranties and support, if applicable, are with UrgentAutomation and not the manufacturer. UrgentAutomation is not an authorized distributor or representative for the listed manufacturers and makes no representations as to any quality control performed by any listed manufacturer on the products. The products listed on this website may vary as to their country of origin; the accessories, and other items included with the product; and the language used on the packaging, the parts, and any related instructions or printed material related to the products. This website is not sanctioned or approved by any manufacturer or tradename listed. Designated trademarks, brand names and brands appearing herein are the property of their respective owners. Read More


FDC2175

Description: The Eaton FDC2175 Molded Case Circuit Breaker is in the C Series and has 2 Pole(s). The module has 175 Trip Amps and a Thermal-Magnetic Trip Unit.

Preowned

Includes a 1-Year UrgentAutomation warranty.

UrgentAutomation is not an authorized distributor for Eaton Cutler-Hammer.


Description: The Eaton FDC2175 Molded Case Circuit Breaker is in the C Series and has 2 Pole(s). The module has 175 Trip Amps and a Thermal-Magnetic Trip Unit.


Rated 4.9 with 18 reviews







About FDC2175

The Eaton FDC2175 is a complete molded case circuit breaker. This module belongs to the FDC Thermal-Magnetic Circuit Breakers Class with non-interchangeable trip units produced by the Eaton Corporation, formerly known as Cutler-Hammer. The FDC2175 is used to cut off the electric supply when an excessive current is detected. The device has 2 poles, and it is applicable to systems connected to 600 Volts AC (50 to 60 Hertz) or to 250 Volts DC voltage sources. The current rating of the FDC2175 is 175 Amps. When users purchase the device, they should check the completeness of the MCCB before installing it. Do not install the device if there is any visible damage to the module. The thermal protection feature of the device will respond to the heat emerging with currents that are higher than the current limit of the device.

The thermal trip occurs with a time delay in response to overloading. This is for the purpose of filtering the short-term current peaks which can normally occur with some types of equipment. When there is a short circuit or a ground fault, the magnetic protection trips instantaneously. The Eaton Cutler-Hammer FDC2175 circuit breaker supports reverse feed usage. It has a highly-isolated plastic housing. The weight of the MCCB is 2 pounds (0.91 kilograms). The module is UL listed and it satisfies the (P1) requirements of the International Electrotechnical Commission Recommendation 157-1 standards. This F-Frame sized circuit breaker is factory-sealed. Its installation procedure consists of connecting and torqueing the line and load terminals. Before that, the circuit breaker should be attached to the mounting panel over the pre-drilled holes.


Technical specifications:


Part Number/Catalog No.FDC2175
Product TypeMolded Case Circuit Breaker
SeriesC
FrameF
Pole(s)2
Trip Amps200 kA at 240 Volts
Interrupting Capacity3 pounds
WeightThermal-Magnetic
Trip Unit2.75 x 6 x 3.38 inches
Part Number/Catalog No.FDC2175
Product TypeMolded Case Circuit Breaker
SeriesC
FrameF
Pole(s)2
Trip Amps200 kA at 240 Volts
Interrupting Capacity3 pounds
WeightThermal-Magnetic
Trip Unit2.75 x 6 x 3.38 inches
Common misspellings:
  • FDC2l75