Eaton Cutler-Hammer
Eaton Cutler-Hammer Drives
Eaton Cutler-Hammer PLC
Eaton Cutler-Hammer Circuit Breakers
Allen Bradley Panelview
Allen Bradley PLC
GE Fanuc
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
Rockwell Disclaimer: The product is used surplus. Urgent Automation is not an authorized surplus dealer or affiliate for the Manufacturer of this product. The product may have older date codes or be an older series than that available direct from the factory or authorized dealers. Because Urgent Automation is not an authorized distributor of this product, the Original Manufacturer’s warranty does not apply. While many Allen-Bradley PLC products will have firmware already installed, Urgent Automation makes no representation as to whether a PLC product will or will not have firmware and, if it does have firmware, whether the firmware is the revision level that you need for your application. Urgent Automation also makes no representations as to your ability or right to download or otherwise obtain firmware for the product from Rockwell, its distributors, or any other source. Urgent Automation also makes no representations as to your right to install any such firmware on the product. Urgent Automation will not obtain or supply firmware on your behalf. It is your obligation to comply with the terms of any End-User License Agreement or similar document related to obtaining or installing firmware.
Urgent Automation is NOT an authorized distributor for this manufacturer and therefore the manufacturer’s warranty does not apply.
Product comes with Urgent Automation's 1-year warranty.
The Eaton Cutler-Hammer D100CR14 is a 14 I/O Micro PLC from D100 series. This is small-sized Programmable Logic Controller (PLC) equipped with 14 I/O (8 inputs + 6 outputs), high-speed counter, and the device is an analog expandable type. It is supplied with 115 Volt AC voltage. Its inputs are a 24 Volt DC type, and its outputs are relays. This module’s software supports 16 timers, 16 counters, 256 steps of step sequencers, and 128 steps of shift registers. The available memory on this device is a 1K RAM memory, which takes close to 8 milliseconds to scan, and this module is a brick-styled stand-alone device. Its installation, connection, and programming procedures are all very simple and the program can be entered via this module’s special feature, a hand-held programmer. This programmer has an LCD and a keyboard. It displays a ladder program which is easily editable.
The programmer device is plugged into the D100CR14 controller, where it receives power, but to gain access to the connector on the controller, the cover labeled “Programmer” must be pushed to the left. Then a program can be entered into the controller via a pre-programmed PROM, or by connecting to a PC and using suitable software, which has certain advantages in easy troubleshooting and reporting. The D100CR14 has only 14 I/O, but it can be expanded with a maximum of two modules to increase its I/O count to 34 in total (20 inputs + 14 outputs). This D100CR14 controller’s ambient working temperature is around 0 to 60 degrees Celsius (32 to 140 degrees Fahrenheit). The controller can be mounted either horizontally or vertically, directly to the panel, using screws or DIN rails. This PLC has dimensions of 9.3 x 6.7 x 1.6 inches (235 x 170 x 40 millimeters).
| Manufacturer | Eaton Cutler-Hammer |
| Brand | Eaton Cutler-Hammer |
| Part Number/Catalog No. | D100CR14 |
| Product Type | 14 I/O Controller |
| Power Supply | 115V AC |
| Inputs | 8 |
| Input Type | 24V DC |
| Outputs | 6 |
| Output Type | Relay |
| System Max I/O Inputs | 20 |
| System Max. I/O Outputs | 14 |
| Capability | High Speed Count and Analog |
| Manufacturer | Eaton Cutler-Hammer |
| Brand | Eaton Cutler-Hammer |
| Part Number/Catalog No. | D100CR14 |
| Product Type | 14 I/O Controller |
| Power Supply | 115V AC |
| Inputs | 8 |
| Input Type | 24V DC |
| Outputs | 6 |
| Output Type | Relay |
| System Max I/O Inputs | 20 |
| System Max. I/O Outputs | 14 |
| Capability | High Speed Count and Analog |